Hyundai Sonata: Brake System / Brake Booster Repair procedures

Hyundai Sonata LF 2014-2019 Service Manual / Brake System / Brake System / Brake Booster Repair procedures

Brake Booster Operating Test

For simple checking of the brake booster operation, carry out the following tests.

1.	Run the engine for one or two minutes, and then stop it. If the pedal depresses fully the first time but gradually becomes higher when depressed succeeding times, the booster is operating properly, if the pedal height remains unchanged, the booster is inoperative.

2.	With the engine stopped, step on the brake pedal several times. Then step on the brake pedal and start the engine. If the pedal moves downward slightly, the booster is in good condition. If there is no change, the booster is inoperative.

With the engine running, step on the brake pedal and then stop the engine.Hold the pedal depressed for 30 seconds. If the pedal height does not change, the booster is in good condition, if the pedal rises, the booster is inoperative.

If the above three tests are okay, the booster performance can be determined as good.

Even if one of the above three tests is not okay, check the check valve, vacuum hose and booster for malfunction.

Removal

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.	Remove the air cleaner assembly (A).

3.	Disconnect the vacuum hose (A) from the brake booster.

4.	Disconnect the brake fluid level switch connector (A).

5.	Remove the master cylinder. (Refer to the Master Cylinder)

6.	Remove the snap pin (A) and clevis pin (B).

Remove the mounting nuts.

Tightening torque:

9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

8.	Remove the brake booster.

[Vacuum Pump]

1.	Turn ignition switch OFF.

Remove the under cover (A).

Tightening torque:

7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

3.	Disconnect the vacuum pump connector (A).

4.	Disconnect the vacuum hose (A).

Loosen the vacuum pump bracket bolts (A), and then remove vacuum pump and bracket.

Tightening torque:

19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

6.	Remove the 2 bolts, and then remove the bracket from vacuum pump.

Inspection

1.	Inspect the vacuum hose, intensifier and the connecting section.

2.	Check the boot for damage.

Vacuum Pump

Check the brake warning lamp in the IGN ON position.

Brake warning lamp is ON as below conditions.

1.	Parking brake warning

2.	Low brake fluid level warning

3.	Low brake vacuum pressure warning

-	Vacuum pump is abnormal condition

-	Vacuum pump CAN communication is abnormal condition

-	Vacuum switch is abnormal condition

Check that the brake warning lamp is ON after the release the parking brake with a sufficient brake fluid level.

If the brake warning lamp is ON, check the below points.

(1)

Is the brake warning lamp ON within 5 seconds after IGN ON? (CAN Timeout Error)

CAN Timeout Error ; The brake warning lamp is ON when the communication fails more than 2 seconds between vacuum pump and cluster.

	? Reinstall the vacuum pump connector after removing it. And if the brake warning lamp is ON within 5 seconds after IGN ON, replace the vacuum pump.
	? Check the 2).

(2)

Is the brake warning lamp ON within 45 ~ 55 seconds?

	? Brake vacuum switch is normal condition.
	? Check the 3).

(3)

Is the brake warning lamp ON within 15 ~ 35 seconds after removing the vacuum hose from the brake booster?

	? Replace the vacuum pump.
	? Vacuum pump is normal condition.

Installation

Brake Booster

Installation is the reverse of removal.

•	Before installing the pin, apply the grease to the joint pin.

•	Use a new snap pin whenever installing.

2.	Adjust the brake pedal height and free play. (Refer to Brake pedal height and free play adjustment)

3.	After installation bleed the brake system. (Refer to Brake System - "Brake System Bleeding") (Refer to ESP (Electronic Stability Program) System - "ESP System Bleeding")

Vacuum Pump

1.	Installation is the reverse of removal.

2.	Tighten the vacuum pump mounting bolts to the specified torque.

Brake Booster Components and Components Location

Components 1. Brake booster2. Reservoir3. Master cylinder4. Pin [T-GDI ENGINE ONLY] 1. Vacuum pump2. Bracket ...

Master Cylinder Components and Components Location

Components 1. Reservoir cap2. Reservoir3. Pin4. Master cylinder ...

Other information:

Hyundai Sonata LF 2014-2019 Owners Manual: Low Tire Pressure Warning Light
This warning light illuminates: Once you set the ignition switch or the Engine Start/Stop button to the ON position. - It illuminates for approximately 3 seconds and then goes off. When one or more of your tires are significantly underinflated (The location of the underinflated tires are di ...

Hyundai Sonata LF 2014-2019 Owners Manual: Charging System Warning Light
If this warning light comes on while the engine is running, the battery is not being charged. Immediately turn off all electrical accessories. Try not to use electrically operated controls, such as the power windows. Keep the engine running; starting the engine will quickly discharge the battery ...