Hyundai Sonata LF: Body (Interior and Exterior) / Floor Console

Hyundai Sonata LF 2014-2019 Service Manual / Body (Interior and Exterior) / Floor Console

Components and Components Location

Components

1. Knob & boots asssembly
2. Upper cover complete
3. Console front complete assembly
4. Console rear complete assembly
5. Console rear mounting bracket

Floor Console Assembly Components and Components Location

Component Location

1. Floor console assembly


Floor Console Assembly Repair procedures

Replacement
   
•
Put on gloves to protect your hands.
   
•
When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the gear knob & boots (A) pull both of it up.

2.
Remove the tray (B) by using remover holder hole after removing the rubber mat (A).

3.
Using a screwdriver or remover, remove the front console upper cover (A).

4.
Disconnect the connectors (A).

5.
Remove the console armrest tray (A).

6.
Remove the storage box pad (A).

7.
After loosening the mounting screws and bolts, then remove the console rear complete assembly (A).

8.
Disconnect the multimedia jcak connectors (A).

9.
After loosening the mounting screws, then remove the console front complete assembly (A).

10.
Install in the reverse order of removal.
   
•
Make sure the connector is connected properly.
•
Replace any damage clips.

Console Armrest Components and Components Location

Component Location

1. Front console armrest


Console Armrest Repair procedures

Replacement
   
•
Put on gloves to protect your hands.
   
•
When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear console cover.
(Refer to Floor Console - "Rear Console Cover")
2.
After loosen the mounting screws, remove the console armrest (A).

3.
Install in the reverse order of removal.
   
•
Make sure the connector is connected properly.
•
Replace any damage clips.

Rear Console Cover Components and Components Location

Component Location

1. Rear console cover


Rear Console Cover Repair procedures

Replacement
   
•
Put on gloves to protect your hands.
   
•
When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Using a screwdriver or remover, remove the rear console cover (A).

2.
Disconnect the connector (A).

3.
Install in the reverse order of removal.
   
•
Make sure the connector is connected properly.
•
Replace any damage clips.

    Cowl Top Cover

    Components and Components Location Component Location 1. Cowl top cover Repair procedures Replacement     • Put on gloves to protect your hands...

    Crash Pad

    ..

    Other information:

    Hyundai Sonata LF 2014-2019 Service Manual: Alternator Schematic Diagrams


    Circuit Diagram     • COM signal - When controlling the voltage generated, the ECM sends the target voltage data to the alternator via a PWM signal.(High voltage: 4V or higher, low voltage: 2V or lower) • FR signal - The transistor activation signal inside the alternator monitors the voltage generated by the alternator to control the excitation current before it sends the FR signal to the ECM...

    Hyundai Sonata LF 2014-2019 Service Manual: Intake Air Temperature Sensor (IATS) Repair procedures


    I..

    Categories

    read more

     
    Copyright © 2026 www.hsonatalf.org