Hyundai Sonata: SRSCM / Side Impact Sensor (SIS) Repair procedures

Hyundai Sonata LF 2014-2019 Service Manual / Restraint / SRSCM / Side Impact Sensor (SIS) Repair procedures

Removal
Pressure Side Impact Sensor
   
Removal of the airbag must be performed according to the precautions/procedures described previously.
Before disconnecting the side impact sensor connector(s), disconnect the side airbag connector(s).
Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
3.
Disconnect the pressure side impact sensor connector (B) and remove the pressure side impact sensor (A).

Gravity Side Impact Sensor
1.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
2.
Remove the door scuff trim.
(Refer to Body - "Interior Trim")
3.
Remove the center pillar trim.
(Refer to Body - "Interior Trim")
4.
Disconnect the side impact sensor connector (A).
5.
Loosen the side impact sensor mounting bolt and remove the side impact sensor (B).

Installation
Pressure Side Impact Sensor
1.
Install the new pressure side impact sensor with the screws then connect the pressure side impact sensor connector.

Tightening torque :
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

   
Use the specified screws surely.
2.
Install the front door trim.
(Refer to Body - "Front Door Trim")
3.
Reconnect the battery negative cable.
4.
After installing the pressure side impact sensor, confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
   
You must comply with the specified tightening torques with the tool specified because Pressure – Side Impact Sensors (P-SIS) may be broken or POP-NUT may be rotated.
Problems may be occurred in the durability of P-SIS or impact sensing performance may be depreciated if POP-NUT is rotated.
The door module must not be transformed because SRSCM judges a impact through the pressure sensor in the door module.
Gravity Side Impact Sensor
   
Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.
1.
Install the new side impact sensor with the bolt then connect the side impact sensor connector.

Tightening torque:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

2.
Install the center pillar trim.
(Refer to Body - "Interior Trim")
3.
Install the door scuff trim.
(Refer to Body - "Interior Trim")
4.
Reconnect the battery negative cable.
5.
After installing the Side Impact Sensor, confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
Side Impact Sensor (SIS) Components and Components Location
Components ...

Seat Belt Buckle Switch (BS) Description and Operation
Description The SRSCM shall monitor the status of the driver and front passenger seat belt buckle. The SRSCM provides one pin each for the driver and front passenger seat belt buckle status inp ...

Other information:

Hyundai Sonata LF 2014-2019 Service Manual: Crankshaft Position Sensor (CKPS) Troubleshooting
Waveform This example shows a typical Crankshaft Position Sensor(CkPS) and Camshaft Position Sensor(CMPS) waveform at idle.The PCM controls the injection and ignition timing by using these signals. Generally CkPS signal is used to detect the piston's position and CMPS signal is used to de ...

Hyundai Sonata LF 2014-2019 Service Manual: Specifications
Specifications ItemSpecificationMaster cylinderTypeSingleI.D. mm(in)NON EPB ?22.22mmEPB?23.81mmPiston stroke mm(in)45±1mm(1.77±0.039in)Fluid level sensorProvidedBrake booster?Type11" SingleBoosting ratio9:01Front disc brakeTypeVentilated discDisc O.DGAMMA1.6 T-GDI305mm (12.0078 in)THETA2 ...

© 2018-2025 www.hsonatalf.org